Aircrack-ng forum
General Category => Newbies => Topic started by: kheemen on October 29, 2013, 05:56:30 pm
-
I have a TP link 725N v2, 8188eu chipped, checked in compat-driver, 8188eu is under staging driver. Does it mean currently unsupported?
Got the driver somewhere and load it, and to scan network using iwlist wlan0 scan, however unable to see any under airmon-ng.
root@bt:/# lsusb
Bus 002 Device 002: ID 80ee:0021 VirtualBox USB Tablet
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 006: ID 0bda:8179 Realtek Semiconductor Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@bt:/# lsmod |grep 818
8188eu 697496 0
root@bt:/# lshw -C network
*-network
description: Ethernet interface
product: 82540EM Gigabit Ethernet Controller
vendor: Intel Corporation
physical id: 3
bus info: pci@0000:00:03.0
logical name: eth0
version: 02
serial: 08:00:27:34:43:44
size: 1GB/s
capacity: 1GB/s
width: 32 bits
clock: 66MHz
capabilities: pm pcix bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=e1000 driverversion=7.3.21-k8-NAPI duplex=full firmware=N/A ip=10.0.2.15 latency=64 link=yes mingnt=255 multicast=yes port=twisted pair speed=1GB/s
resources: irq:19 memory:f0000000-f001ffff ioport:d010(size=8)
*-network DISABLED
description: Wireless interface
physical id: 1
bus info: usb@1:1
logical name: wlan0
serial: 64:66:b3:27:a4:14
capabilities: ethernet physical wireless
configuration: broadcast=yes driver=r8188eu multicast=yes wireless=unassociated
root@bt:/# iwconfig
lo no wireless extensions.
wlan0 unassociated Nickname:"<WIFI@REALTEK>"
Mode:Auto Frequency=2.412 GHz Access Point: Not-Associated
Sensitivity:0/0
Retry:off RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
eth0 no wireless extensions.
root@bt:/# airmon-ng
Interface Chipset Driver
I had another rt2800 usb which is working very fine...
Any help on 8188eu ? or it just won't work?..
-
any one can help?..
-
Could you show me the part of dmesg about when you load the driver.
The easiest way is to unplug it, unload the 8188eu module, clearing dmesg then plug it again.
-
dmesg when it load the driver:
[ 196.148048] usb 1-1: new high-speed USB device number 2 using ehci_hcd
[ 196.516684] register rtw_netdev_ops to netdev_ops
[ 196.516687] CHIP TYPE: RTL8188E
[ 196.516692]
[ 196.516692] usb_endpoint_descriptor(0):
[ 196.516693] bLength=7
[ 196.516694] bDescriptorType=5
[ 196.516695] bEndpointAddress=81
[ 196.516696] wMaxPacketSize=512
[ 196.516697] bInterval=0
[ 196.516698] RT_usb_endpoint_is_bulk_in = 1
[ 196.516699]
[ 196.516699] usb_endpoint_descriptor(1):
[ 196.516700] bLength=7
[ 196.516701] bDescriptorType=5
[ 196.516702] bEndpointAddress=2
[ 196.516702] wMaxPacketSize=512
[ 196.516703] bInterval=0
[ 196.516704] RT_usb_endpoint_is_bulk_out = 2
[ 196.516705]
[ 196.516706] usb_endpoint_descriptor(2):
[ 196.516707] bLength=7
[ 196.516707] bDescriptorType=5
[ 196.516708] bEndpointAddress=3
[ 196.516709] wMaxPacketSize=512
[ 196.516710] bInterval=0
[ 196.516711] RT_usb_endpoint_is_bulk_out = 3
[ 196.516712] nr_endpoint=3, in_num=1, out_num=2
[ 196.516713]
[ 196.516714] USB_SPEED_HIGH
[ 196.526227] Chip Version Info: CHIP_8188E_Normal_Chip_TSMC_D_CUT_1T1R_RomVer(0)
[ 196.526231] RF_Type is 3!!
[ 196.526233] _ConfigNormalChipOutEP_8188E OutEpQueueSel(0x05), OutEpNumber(2)
[ 196.528611] EEPROM type is E-FUSE
[ 196.528614] ====> _ReadAdapterInfo8188EU
[ 196.531602] Boot from EFUSE, Autoload OK !
[ 199.540670] EEPROM ID=0x8129
[ 199.540672] VID = 0x0BDA, PID = 0x8179
[ 199.540674] Customer ID: 0x00, SubCustomer ID: 0xCD
[ 199.540676] Hal_ReadPowerSavingMode88E...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(0)
[ 199.540678] ### PS params=> power_mgnt(1),usbss_enable(0) ###
[ 199.540680] ======= Path 0, Channel 0 =======
[ 199.540683] Index24G_CCK_Base[0][0] = 0x2a
[ 199.540684] Index24G_BW40_Base[0][0] = 0x2e
[ 199.540685] ======= Path 0, Channel 1 =======
[ 199.540687] Index24G_CCK_Base[0][1] = 0x2a
[ 199.540688] Index24G_BW40_Base[0][1] = 0x2e
[ 199.540689] ======= Path 0, Channel 2 =======
[ 199.540690] Index24G_CCK_Base[0][2] = 0x2a
[ 199.540691] Index24G_BW40_Base[0][2] = 0x2e
[ 199.540692] ======= Path 0, Channel 3 =======
[ 199.540693] Index24G_CCK_Base[0][3] = 0x2a
[ 199.540694] Index24G_BW40_Base[0][3] = 0x2e
[ 199.540695] ======= Path 0, Channel 4 =======
[ 199.540697] Index24G_CCK_Base[0][4] = 0x2a
[ 199.540698] Index24G_BW40_Base[0][4] = 0x2e
[ 199.540699] ======= Path 0, Channel 5 =======
[ 199.540700] Index24G_CCK_Base[0][5] = 0x2a
[ 199.540701] Index24G_BW40_Base[0][5] = 0x2e
[ 199.540702] ======= Path 0, Channel 6 =======
[ 199.540703] Index24G_CCK_Base[0][6] = 0x29
[ 199.540704] Index24G_BW40_Base[0][6] = 0x2d
[ 199.540705] ======= Path 0, Channel 7 =======
[ 199.540706] Index24G_CCK_Base[0][7] = 0x29
[ 199.540708] Index24G_BW40_Base[0][7] = 0x2d
[ 199.540709] ======= Path 0, Channel 8 =======
[ 199.540710] Index24G_CCK_Base[0][8] = 0x29
[ 199.540711] Index24G_BW40_Base[0][8] = 0x2d
[ 199.540712] ======= Path 0, Channel 9 =======
[ 199.540713] Index24G_CCK_Base[0][9] = 0x29
[ 199.540714] Index24G_BW40_Base[0][9] = 0x2c
[ 199.540715] ======= Path 0, Channel 10 =======
[ 199.540716] Index24G_CCK_Base[0][10] = 0x29
[ 199.540718] Index24G_BW40_Base[0][10] = 0x2c
[ 199.540719] ======= Path 0, Channel 11 =======
[ 199.540720] Index24G_CCK_Base[0][11] = 0x29
[ 199.540721] Index24G_BW40_Base[0][11] = 0x2c
[ 199.540722] ======= Path 0, Channel 12 =======
[ 199.540723] Index24G_CCK_Base[0][12] = 0x29
[ 199.540724] Index24G_BW40_Base[0][12] = 0x2c
[ 199.540725] ======= Path 0, Channel 13 =======
[ 199.540726] Index24G_CCK_Base[0][13] = 0x29
[ 199.540728] Index24G_BW40_Base[0][13] = 0x2c
[ 199.540729] ======= Path 0, Channel 14 =======
[ 199.540730] Index24G_CCK_Base[0][14] = 0x29
[ 199.540731] Index24G_BW40_Base[0][14] = 0x2c
[ 199.540732] ======= TxCount 0 =======
[ 199.540733] CCK_24G_Diff[0][0]= 0
[ 199.540734] OFDM_24G_Diff[0][0]= 1
[ 199.540735] BW20_24G_Diff[0][0]= -1
[ 199.540736] BW40_24G_Diff[0][0]= 0
[ 199.540737] ======= TxCount 1 =======
[ 199.540738] CCK_24G_Diff[0][1]= -2
[ 199.540739] OFDM_24G_Diff[0][1]= -2
[ 199.540740] BW20_24G_Diff[0][1]= -2
[ 199.540741] BW40_24G_Diff[0][1]= -2
[ 199.540742] ======= TxCount 2 =======
[ 199.540743] CCK_24G_Diff[0][2]= -2
[ 199.540744] OFDM_24G_Diff[0][2]= -2
[ 199.540745] BW20_24G_Diff[0][2]= -2
[ 199.540746] BW40_24G_Diff[0][2]= -2
[ 199.540747] ======= TxCount 3 =======
[ 199.540748] CCK_24G_Diff[0][3]= -2
[ 199.540749] OFDM_24G_Diff[0][3]= -2
[ 199.540750] BW20_24G_Diff[0][3]= -2
[ 199.540751] BW40_24G_Diff[0][3]= -2
[ 199.540752] EEPROMRegulatory = 0x0
[ 199.540754] mlmepriv.ChannelPlan = 0x20
[ 199.540755] EEPROM Customer ID: 0x 0
[ 199.540756] EEPROM : AntDivCfg = 0, TRxAntDivType = 3
[ 199.540758] Board Type: 0x 0
[ 199.540758] ThermalMeter = 0x1a
[ 199.540760] <==== _ReadAdapterInfo8188EU in 3012 ms
[ 199.540955] rtw_macaddr_cfg MAC Address = 64:66:b3:27:a4:14
[ 199.540957] MAC Address from pnetdev->dev_addr= 64:66:b3:27:a4:14
[ 199.541224] bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0
But the iwlist scan can return result, same as Wicd :
root@bt:/# iwlist wlan0 scan
wlan0 Scan completed :
Cell 01 - Address: F8:D1:11:B0:B2:B2
ESSID:"XXXXXXXXXXX"
Protocol:IEEE 802.11bgn
Mode:Master
Frequency:2.447 GHz (Channel 8)
Encryption key:on
Bit Rates:150 Mb/s
Extra:wpa_ie=dd1a0050f20101000050f20202000050f2040050f20201000050f202
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (2) : CCMP TKIP
Authentication Suites (1) : PSK
Extra:rsn_ie=30180100000fac020200000fac04000fac020100000fac020000
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (2) : CCMP TKIP
Authentication Suites (1) : PSK
IE: Unknown: DD9E0050F204104A00011010440001021057000101103B0001031047001000000000000010000000F8D111B0B2101021000754502D4C494E4B10230009544C2D4D523330323010240003312E3010420003312E301054000800060050F204000110110019576972656C65737320526F7574657220544C2D4D5233303230100800020086103C000101104900140024E26002000101600000020001600100020001
Quality=64/100 Signal level=74/100
-
Thanks. I have no idea why it didn't detect it. I ordered the card so I can have a look at it and fix airmon-ng. In the meantime, try airmon-zc
-
Result:
root@bt:/# airmon-zc
This script is intended to replace airmon-ng in 1.3 and is functionally based on it.
Please test and report bugs to Zero_Chaos on freenode in #aircrack-ng or on trac
Linux bt 3.2.6 #1 SMP Fri Feb 17 10:34:20 EST 2012 x86_64 GNU/Linux
Detected VM using lscpu
This appears to be a VirtualBox Virtual Machine
If your system supports VT-d, it may be possible to use PCI devices
If your system does not support VT-d, you can only use USB wifi cards
K indicates driver is from 3.2.6
C indicates driver is from compat-drivers-2012-12-14-3-p
V indicates driver comes directly from the vendor, almost certainly a bad thing
S indicates driver comes from the staging tree, these drivers are meant for reference not actual use, BEWARE
? indicates we do not know where the driver comes from... report this
X[PHY]Interface Driver[Stack]-FirmwareRev Chipset Extended Info
lspci: -d: ':' expected
ERROR: modinfo: could not find module ??????
ERROR: modinfo: could not find module ??????
ERROR: modinfo: could not find module ??????
ERROR: modinfo: could not find module ??????
?[null]wlan0 ??????[ieee80211]-unavailable Realtek Semiconductor Corp. Failure detecting driver properly please report